CRT
|
Configuration and Useful Screen |
6-inch rectangular screen
with internal graticule: 8x 10div(1div=1cm), marking for measurement of rise
time, 2mm subdivisions along the central axis |
|
Acceleration Potential |
+11.5kv approx. (ref.
Cathode) |
|
Phosphor |
P31 (Standard) |
|
Focusing |
Possible (with auto-focus
correction circuit) |
|
Trace Rotation |
Provided |
|
Scale Illumination |
Variable |
|
Intensity Control |
Provided |
|
Z-AXIS INPUT (Intensity
modulation) |
Input signal |
Positive going signal
decreases +5Vp-p or more signal cases noticeable modulation at normal
intensity settings |
|
Bandwidth |
DC to 2MHz (-3dB) |
|
Coupling |
DC |
|
Input Impedance |
20kW
-30kW
typical |
|
Maximum Input Voltage |
30V (DC + peak AC) |
VERTICAL
DEFLECTION |
Bandwidth
(-3dB) |
DC
coupled |
DC to 100MHz (2mV/DIV:DC
to 50MHz) |
|
AC
coupled |
10Hz to 100MHz
(2mV/DIV:10Hz to 50MHz) |
|
Modes |
CH1, CH2, ADD, DUAL, ALT,
CHOP, CH2 INV. QUAD |
CH1, CH2, DUAL, ADD, ALT,
CHOP, CH2 INV. |
|
Deflection Factor |
2mV/Div to 5V/Div in 11
calibrated steps of 1-2-5 sequence. ( For CS 6100: CH3, CH4:0.1V/DIV,
0.5/DIV) Continuously variable between steps at least 1:2.5 |
|
Accuracy |
±3% |
|
Input Impedance |
Approx. 1MW
in parallel with
25pF |
|
Maximum Input Voltage |
Direct: 400V (DC+ peak
AC), with probe: refer to probe specification |
|
Input Coupling |
DC-GND-AC |
|
Rise
Time |
3.5ns or less (2mV/DIV:
7ns or less) |
|
CH1
Out |
50mV/Div into 50W
: DC to
20MHz(-3dB) |
|
Polarity Inversion |
CH2 Only |
|
HORIZONTAL
DEFLECTION |
Display Mode |
A,ALT,B,B TRIG’ D, X-Y |
|
Time Base
A |
0.05us/Div to 0.5s/Div in
22 calibrated steps of 1-2-5 sequence, Uncalibrated continuous control
between steps at least 1:2.5 |
|
Hold-off
Time |
Variable with the
hold-off control |
|
Time Base
B |
0.05us/div to 50ms/div in
19 calibrated steps of 1-2-5 sequence |
|
Delayed
Sweep Position |
1div or less – 10div or
more |
|
Delay Time
Jitter |
Better than 1:10,000 |
|
Sweep Magnification |
10 times (Maximum sweep
rate: 5ns/div) |
|
Accuracy |
±3%, ±5% (0°C to 40°C),
additional error for magnifier ±2% |
|
TRIGGER
SYSTEM |
Modes |
AUTO, NORM, TV, SINGLE |
|
Source |
LINE, VERT, CH1, CH2,
CH3, CH4 |
LINE, VERT, CH1, CH2 |
|
Coupling |
AC,DC,HF REJ,LF REJ,
TV-V, TV-H |
|
Slope |
+ or - |
|
Sensitivity and Frequency AUTO(30Hz or more), NORM |
|
20Hz – 2MHz |
2MHz – 40MHz |
|
INT |
0.5div |
1.5div |
|
EXT |
0.1Vp-p |
0.3Vp-p |
|
VERT |
0.5div |
3.0div |
|
TV-V, TV-H |
At least 1div or 1.0Vp-p |
|
External Trigger Input Impedance |
1MW
in parallel with
approx. 25pF |
|
Maximum Input Voltage |
400V (DC+ peak AC) |
X-Y
OPERATION |
X-Axis |
(same as CH1 except for
the following)
Deflection factor; same
as that of CH1 / Accuracy: ±6% / Frequency response: DC to 2MHz(-3dB) |
|
Y-Axis |
Same as CH2 |
|
X-Y
Phase Difference |
3°
or less (at DC to 100kHz) |
|
READOUT
FUNCTION |
Cursor readout function |
DV,
DT,
D1/T |
|
Auto
setup |
Enable |
|
Frequency Counter Displays |
Enable (only on Autosetup) |
|
Panel setting displays |
AC/DC/GND, V-MODE, CH2
Invert, VOLTS/DIV, * 10MAG, H-DSP MODE, TIME/DIV, TRG COUPLING, TRIG SOURCE. |
|
Effective cursor range from centre graticule |
Vertical: within ±3div /
Horizontal: within ± 4div |
|
Resolution |
1/25 div |
CALIBRATOR
|
Probe Adjustment |
Approx, 1KHz 0.5Vp-p
(±2%)Square wave, duty ratio: 50% |
POWER
SUPPLY |
Line
Voltage Range |
90~250VAC(fuse:1A 250V) |
|
Line
Frequency |
48 / 440Hz |
|
Power Consumption |
Max. 50W |
|
PHYSICAL
CHARACTERISTIC |
Weight |
8kg |
|
Size |
328mm(W) x 153mm(H) x
392mm(L) |
|
ENVIRONMENTAL
CHARACTERISTIC |
Temperature |
Temperature range for
rated operation: +10°C to +35°C (+50°F to +95°F)
Max, ambient operating
temperature: 0°C to +40°C (+32°F to +104°F)
MAX, storage temperature:
-20°C to 70°C (-4°F to +158°F) |
|
Humidity |
Range for rated
operation:45% to 85% RH / Max. Ambient operating humidity : 35% to 90% RH |
|
OTHERS |
Accessories supplied |
Operator’s manual, Spare
fuse, Power cord, Test probe. |
